Frequent question: What do you do when your radio says protect?

If that’s the case, fixing the problem is simple. Turn off the receiver and let it cool for a few hours; then try again. If the protection mode warning doesn’t go away on its own, press the reset button. If that doesn’t work, disconnect the power lead from your receiver for 30 seconds and then reconnect it.

Why is my radio saying protect?

If the impedance of any of the speakers is below the rated impedance range indicated on the rear of the home audio device next to the speaker connections, the home audio device may enter the PROTECT mode. Raising the volume with a low impedance speaker will trigger the protection circuit.

How do I get my Kenwood out of Protect Mode?

This is the best quick fix to repair any Kenwood headunit that is stuck into protect mode:

  1. Switch on the CD Player.
  2. Remove the front panel.
  3. Find the reset button and place something into it for 5 seconds.
  4. Its should release itself from the protect mode and reset.
IT IS INTERESTING:  Why did protective tariffs harm Southerners?

How do I reset my Kenwood radio?

Kenwood Factory Reset

  1. Step 1: Hold Eject CD And Volume button. On the left of the CD slot, you will find the Eject CD button. …
  2. Step 2: Press The Reset Button. …
  3. Step 3: Tap the “Initialize All” button. …
  4. Step 4: Again, press the reset button.

How do I fix JVC protect mode?

Registered

  1. Disconnect all power from the unit.
  2. Simultaneously press and hold the [MENU] and [Skip Track] buttons.
  3. While holding down both [MENU] and [Skip Track] , apply 12v power to unit. …
  4. Press [Skip Track] until the display shows “DC1 ERR” …
  5. Press [Pause] and advance display until “DC2” appears.

Why does my radio not work after changing battery?

The most common reason for a car radio to stop working after the battery has gone completely dead is that the radio has an anti-theft “feature” that kicks in whenever battery power is removed. When that happens, all you have to do is enter the right car radio code, and you’re back in business.

What does HF Error 68 mean?

ö “HF ERROR 68” Í The unit cannot communicate with the cell-phone. ò Cycle the power switch. If this message still appears, press the Reset button on the control unit.

Why did my Kenwood radio stopped working?

Blown Fuse

If the radio will not turn on, first check the fuse located on the back of the radio. If the fuse is burnt, replace with a fuse of the same amperage rating. The guide to replacing the fuse can be found here.

IT IS INTERESTING:  Are mutual funds listed securities?

What is a Miswiring DC offset error?

If the power is not turned ON (“Miswiring DC Offset Error”, “Warning DC Offset Error” is displayed), the speaker wire may have a short- circuit or touched the chassis of the vehicle and the protection function may have been activated. Therefore, the speaker wire should be checked.

Why is my Kenwood amp light red?

the red light is obviously a distress light so check the wiring its most likely wired at too low impedandce for the amp to take. did the amp overheat? gain set all the way up over-driving the input stage of the amp and causing the amp to enter protection.

How do I reset my car radio without the code?

Turn on your radio and see if it displays CODE or LOC. If it does, turn off the radio. Press and hold down the audio power button together with the SEEK button for about 50-60 minutes. Then, it will turn on without entering the radio code.

How do you fix a Kenwood radio when it says protect?

If that’s the case, fixing the problem is simple. Turn off the receiver and let it cool for a few hours; then try again. If the protection mode warning doesn’t go away on its own, press the reset button. If that doesn’t work, disconnect the power lead from your receiver for 30 seconds and then reconnect it.

Where is the menu button on my JVC remote?

Select the MENU button on the top right corner of the screen.