How do you reset the security system on a Chevy Silverado?

In a chevy silverado, you will try to reset the anti-theft system by turning the key on until the yellow lock goes out on the instrument panel for about 10 minutes. Turn the key off and do it 2 more times after 3 cycles, pull the key and put it back in.

How do I get my truck out of theft mode?

Method 3: Insert the key into your car’s door

Step 1: Insert the key into the door lock. Use the side door on the driver’s side and the physical key even if there is a keyless entry system on the car. Step 2: Turn the vehicle key to unlock the car door without releasing it. Hold the key for 30 seconds in the position.

How do you reset the security system on a 2002 Chevy Silverado?

To reset Your 2002 Chevy Silverado security system put the key in the ignition, turn the key to the on position, and leave it on until the security light goes out. Usually 15min. Once this happens crank the truck without turning the key backward, just turn to start.

IT IS INTERESTING:  What is tag in McAfee ePO?

How do I reset my GM security system?

How to Reset the Passlock System on GM Cars

  1. Insert your key in the starter, start you car as you usually would and let it stall. Keep the key in the “On” position. …
  2. Wait until the “Theft Sys” light on your dashboard stays on without blinking. This will take approximately 10 to 15 minutes.

How do you reset the security system on a 2003 Chevy Silverado?

Resetting the 2003 Chevrolet Silverado security system is easy, and takes about 5 to 10 minutes. The first thing You need to do is open the driver’s side door, and sit down inside. Next, place Your key in the ignition, and turn it to the on position. Be careful not to actually start the motor when You do this.

How do I get my car out of anti-theft mode without remote?

Resetting the Alarm

  1. Close all of your car doors.
  2. Insert one key in the door lock and cycle it to the “Lock” position, and then back to the “Unlock” position two times. …
  3. Enter your car and insert your key into the ignition cylinder.
  4. Cycle the key in the ignition from the “Off” position to the “On” position twice in a row.

Will disconnecting battery reset anti-theft?

By unplugging the battery for a few minutes, it will also reset the computer. … All you have to do is disconnect the positive or negative terminal and wait.

How do I bypass PASSLock GM security system?

Thankfully this is an easy fix.

  1. Leave the ignition key turned to the “On” position after the vehicle has stalled and will not start.
  2. Look at the dashboard and locate the theft system light. …
  3. Turn the ignition to the “Off” position to disable the PassLock system, and wait for 20 seconds for the system to reset.
IT IS INTERESTING:  How do I send money to a Security bank?

How do you reset the security system on a 2000 Chevy Silverado?

Leave the ignition switch in the “Run” position as the “Security” light blinks on and off for approximately 10 minutes. Turn the ignition switch clockwise to start the engine immediately after the “Security” light stops flashing. The Passlock system resets and the engine will start.

What triggers theft deterrent system?

The theft-deterrent system in your vehicle may be triggered by the following: Key learning (copy of key made) Forced entry alarm (door, trunk, hood) … Charging alarm (electric vehicles only)

How do you reset the anti-theft system on a 2014 Chevy Silverado?

To reset the anti-theft system in the 2014 Chevy Silverado, turn the key in the ignition to the “on” position and attempt to fire the engine. Return to the “on” position. The vehicle will not start if anti-theft has disabled the ignition. After 10 minutes, the flashing “security” warning light should power off.

Is there a fuse for the anti-theft system?

Is there a fuse for anti theft system? The alarm fuse is located in the fuse panel of most cars. Using the owner’s manual remove the fuse which will power down the security system. At this point the car will not start, reinsert the fuse to reactive the system.

Can you bypass PATS system?

Can you bypass the PATS system? Yes, there is a simple way to bypass the pats system on your own. All you need is the transponder key to trick the system. By having the transponder key, you can remove the chip inside the key and glue it to the ignition and use any key that matches the original to start up the engine.

IT IS INTERESTING:  How do you protect the rights and confidentiality of patients?

How do I disable GM Anti-theft system?

The vehicle should start, and then stall while the SECURITY light flashes. Leave the key at the ON position for 10 minutes and wait for the SECURITY light to go away. Turn the key to the OFF position for 5 seconds and restart the car. The car should start and the SECURITY light should remain off.

How do I know if my PASSLock is activated?

Most PASSLock-equipped vehicles have a telltale indicator in the instrument panel. When a PASSLock-equipped vehicle is being started, the instrument panel warning light for PASSLock remains on until the engine starts.

Where is PASSLock sensor located?

The Passlock III system uses a transponder located under the plastic covering of the key. In most cases, these keys are stamped “PK3” on the metal blade near the plastic covering.